Osmo Polyx-Oil Clear Matte

$64.00$172.00

THE ORIGINAL HARDWAX OIL

Osmo Polyx®-Oil is a general purpose Hardwax-Oil wood finish that is derived from natural vegetable oils and waxes.

Clear
SKU: 3031 Categories: , ,

Product Description

Our Easiest Application Yet

Osmo Polyx®-Oil is a general purpose Hardwax-Oil wood finish that is derived from natural vegetable oils and waxes. Resistant to water, dirt, beer, wine, cola and saliva, Osmo Polyx-Oil is microporous and molecularly bonds with the wood, meaning it does not crack, flake, peel or blister.

Our new advanced formula of Polyx-Oil has been specially engineered in Germany to be the first Hardwax-Oil available on the North American market that can be easily applied with a brush or roller, with no buffing necessary! Can be spot-repaired and/or restored/renewed with no sanding required, therefore wood never needs complete sanding and refinishing again.

Available Osmo Polyx-Oil Colour Tones

3043 – Clear Satin

3031 – Clear Matte

Note: The above colour shades are a true likeness of the original, after application onto Oak. However, some variation may occur due to screen brightness and uploading processes. It is advisable to test colours on a small sample, as colour may appear differently on other wood species.

MECHANICALLY WITH A BRUSH OR ROLLER; AND FLOOR BUFFER

First Coat: Apply one thin coat with an Osmo Floor Brush or Osmo Floor Roller.

  1. Stir the Polyx®-Oil well and prior to use
  2. Brush or roll the product thinly and evenly onto the floor.
  3. Do not remove excess product, this will absorb into the wood surface over the drying period
  4. Allow 8-10 hours drying time prior to proceeding to second coat

Second Coat: Roll or Brush a thin second coat and remove all excess with a buffing machine

  1. Brush or roll the second coat thinly and evenly onto the floor
  2. Allow approximately 5-10 minutes for product to penetrate surface
  3. Prior to buffing, remove excess product from room corners with a white pad
  4. Disperse and polish the floor, removing all excess using a floor buffer and white pads.
  5. There is too much on the surface when you can see swirls or rings. If so turn the pad over.
  6. Allow 8-10 hours drying time. Allow for good ventilation whilst drying.

Third Coat: Usually a third coat is not required, however highly absorbent or dry timbers may appear to require a third coat.

Please consult OSMO technical support at 1-844-OSMOCAN prior to carrying out a third coat

Tinting: Osmo Wood Wax Finish can also be used to lightly tint Polyx®-Oil 3054 up to a ratio of 10:1. Do not exceed a ratio of 10 parts Polyx®-Oil 3054 to 1 part Wood Wax Finish.

Ex. For Natural (no colour change from raw wood) tint Polyx-Oil with Wood Wax Finish 3111 White at 3% for the base-coat, followed by a coat of clear (untinted) Polyx-Oil as a top-coat.

Cure Period: Osmo Hardwax-Oil(s) like all floor finishes have a cure period. We recommend allowing 2 weeks for the surface to fully cure and harden prior to damp-mopping or placing rugs/mats on the surface.

BY HAND WITH A CLOTH/RAG

Apply three thin coats with a lint-free microfibre cloth. ie. Osmo Easy Pads.

  1. Stir the Polyx®-Oil well and prior to use
  2. Work product into wood using cloth in a circular or figure 8 pattern
  3. Allow roughly 15-minutes for oils to penetrate
  4. Working with the grain, remove all excess product from surface
  5. Allow 8-10 hours drying time prior to recoating
  6. Apply second and third coats following previous steps

WARNING: Cloths saturated with product are a spontaneous combustion hazard and should be left out unfolded until dried, prior to disposal or preferably stored in a proper fireproof container

BY HAND WITH SCOTCHBRITE PADS

Apply two thin coats with non-abrasive white scotchbrite pads

  1. Stir the Polyx®-Oil well and pour into tray
  2. Work the product into the wood thinly and evenly in figure 8 or circular motions using a white pad
  3. Be sure to thinly and evenly coat the surface and leave on the surface for approx. 5 minutes
  4. With a clean white pad, polish the surface ensuring no swirl marks, rings, or wipe marks
  5. Ensure all excess product is removed from surface
  6. Allow approx. 8-10 hours drying time. Allow for good ventilation whilst drying
  7. Apply second coat following previous steps.
Approx. Coverage
24m²/L (258 ft2/L) with one coat
Number of Coats
2 coats
Application Temp.
+5°C to 35°C
Approx. Dry Time
8-10hrs.
Sizes
5mL, 0.125L, 0.750L, 2.5L, 10L
  • Easy to apply – used by both professionals and homeowners
  • Extremely durable and hardwearing
  • Can be spot-repaired and refreshed with no sanding required
  • Microporous finish which does not crack, peel or flake
  • Very water and dirt resistant as well as juice, tea, cola, wine, beer, coffee.
  • Enhances the wood’s natural character
  • Saliva-resistant and sweatproof, suitable for children’s toys

Additional Information

Weight 2.9 kg
Dimensions 16.5 x 16.5 x 16.5 cm
Size

.75L, 2.5L

Reviews

There are no reviews yet.

Be the first to review “Osmo Polyx-Oil Clear Matte”

Your email address will not be published. Required fields are marked *